1970 BUICK Skylark Street Sleeper
1970 Buick Skylark for sale in Bainbridge Island, Washington, United States
Item location: | Bainbridge Island, Washington, United States |
Make: | Buick |
Model: | Skylark |
Type: | Coupe |
Year: | 1970 |
Mileage: | 1000 |
VIN: | 435370xxxxxxx |
Color: | Blue |
Number of cylinders: | 8 |
Transmission: | Manual |
Drive type: | RWD |
Interior color: | Blue |
Drive side: | Left-hand drive |
Vehicle Title: | Clean |
Want to buy? | Contact seller! |
Description for Buick Skylark 1970
1970 BUICK SKYLARK - HOLIDAY COUPE- “STREET SLEEPERâ€
Sorry the pictures don’t do it justice.
This car is built for dependable street and strip action. Using a combination of top qualityN.O.S and OEM parts that matter, andTop Name brand aftermarket drivetrain & suspension parts that matter even more. The 462cid BUICK 4 Speed drivetrain and systems are solid, suspension is top notch, body solid and interior is gorgeous withnew & like new original. No expenses spared on the parts and build.
Fully NHRA tech approved, car is a track ready, turn key, and local car show favorite, street driven to the track, peel off some runs and stop by the grocery store on the way home....pulling the race trailer too.
In summer of 2017, I made three trips to the local race track at Bremerton, WA. Twelve passes and she clockedregular quarter miles of 12.15 -12.50@ blistering 114MPH - 117MPH with agonizing 1.8 - 2.0 @ 60' times. The rock crusher 2.20 first gear heldthe 60'sback.Last yearI upgraded the M22 toa fullrace duty Autogear casedM23, with all the bestinternal parts.It has 2.99 first gear making launch ratio with the 3.7 rear and tire combination absolutely optimal and should yield 1.4-1.5 @ 60' times and correlating mid 11's in the quarter (naturally aspirated). I have not run the nitrous through this engine but it is all ready to go and would yield another second no doubt.
Body has been left alone for patina sake and sleeper attire. It is solid NW car.There are some small rust spotsthat I treated with phosphoric acidwhen I had the body off.
Everything replaced when I had the body off. Hard to find a more solid, well built car and my loss is buyers gain.
Also have1970 dealer installed DrawTie trailer hitch, and a plug and play wire pigtail which was made to not splice into the factory wires (clever). Load the tools, tire and track amenities, and drive this racecar with its race trailer to the track. (trailer not included)
Since I built it, I have put around 1000 miles on most of it. The new trans has less than 500 miles on it. She lives in a heated garage and does not get out nearly enough which is why I am deciding to find her a new caretaker. Includedwith the sale are all receipts for parts totaling over $47,000 dollars and over 450 manhours. (See the ledgerbelow). Thebuild is professionally done right, no missing pieces, shoddy work, corners cut, etc...
Purchase also includes the front and rear Drag Wheels and Tires, an extra mint 1970 hood, the power steering parts, the 1-1/4" front sway bar and bushings, the hood latch assembly, the carb jet & air bleed & N2Otuning jet kits, spare MSD rotors and caps, new spark plugs, four new 5 gallon race fueljugs, the backup N2O bottle, and all thereceipts and installation manuals and documents for al the parts.
Here are the details:
The car was barn stored between 1999 – 2013. I acquired the car spring of 2013as arolling shell with all of her original sheet metal, chrome / trim andsome of her original interior which was in good condition. Icompleted a Body-Off Re-build & Drag Race Prep between March 2013 – June 2016, and have continued upgrades since. Manufactured 10/69, BUICK Fremont, CA. Plant. Non A/C, clock, rear defog, map light, trunk light, only factory options. Gulfstream Blue exterior GM 25 (repainted est. 1986). Original to the car are the two tone blue door panels, the kick panels, sail panels visors and headliner. New carpet, metal dash refinished, rebuilt front bench and rear bench with new PUI seat covers.
Engine is a 1972 BUICK 455, Bore 4.3425†x Stroke 3.9â€= 462†Cubic Inches Displacement. 550 Ft/lbs. Torque / 500 Horse Power, [Naturally Aspirated] @ Engine Dyno. Balanced rotating assembly, deck set -0.020â€, TRW Forged Aluminum Pistons, peened and resized Con Rods, Blueprinted Oil Pump, Race bearings, ARP Fasteners. 9.65:1 Final DCR.
T/A Stage 1 Aluminum Street Eliminator heads, 2.125†x 1.75†Stainless swirl valves, Full Race Ported, flow 340 Intake / 240 Exhaust, 60 cc. Port Matched Edelbrock Performer aluminum Intake manifold, center plenum cut out and blended. AMP baffle installed. Cometics 0.019" head gaskets.
Bullet 228*/0.520†x 233*/0.525â€, 112LSA / 108* CL, Hydraulic Johnson Lifters. T/A Roller Rockers 1.6:1 & 3/8†Chrome Moly pushrods
Doug’s 1-7/8†x 3†Jet Hot Coated Headers, Torque Tec 2-1/2†w/ x pipe crossover tubes factory style tail pipes, Walker Dynomax 20†mufflers. Crankcase evacuation system plumbed into head pipes.
Proform 950 Carburetor, 0.080†primary & 0.086†secondary jet, 33/79 Primary & 35/79 Secondary Squirters / Air Horns, 2" Wilson tapered carb spacer manifold base plate.
NOS Kenne-Bell Tall Valve Covers, T/A [reproduction] Kenne-Bell Stage 2 Hood Scoop, K&N Hi-Flow Air Filter.
RobbMc 1100 Race Fuel pump & fuel pressure regulator, -8AN fuel tank pickup & fuel lines, RobbMc 100Micron & 80Micron filters.
Nitrous Supply Inc, †Sports Star plate, 0.047" N20 and 0.043" Fuel jets, 6.5 psi fuel switch, carb mounted WOT switch, NEX Bottle Heater, push button system purge, pressure blow-off valves, set for 100 HP shot. RCI 1 gallon dedicated fuel tank, Comp Cams 45PGH fuel pump, Edelbrock fuel pressure regulator, RobbMc 100Micron & 80Micron filters.
Mallory fully programmable HyFire IV Digital Timing control Box, MSD Starter Saver, MSD 8517 Pro Billet Distributor, locked out 36* timing, MSD 8.5mm Super Conductor plug wires, MSD Blaster 3 Coil.
Quick Performance GM 9â€, Fabricated Steel Center Section, †heavy walled axle tube, aluminum through bolt center section with 35 spline axles, Yukon locker, 1350 series billet yoke, Aluminum Daytona pinion support & 3.70 ratio ring & pinion. 3â€/20 axle studs.
Rear Speedway 15 x 8 GM Steel Wheels w/ Dog Dish Hub Caps – 275/60/15 Mickey Thompson Drag Radial. Front OEM 1970 GM 15x7 Steel Wheels w/ Dog Dish Hub Caps - 245/60/15 BF Goodrich Radial T/A. Race Slicks are Mickey Thompson Drag ET - 29x9x15, tubed and screwed and 25/4.4/15 mounted to vintage Cragar Super Tricks.
Race Prepped Muncie Auto Gear M-23. 2.99-1.88-1.35-1:1. Wilwood Hydraulic Clutch Pedal with American Powertain Hydramax throw out bearing. SFI Certified Lakewood Blow Proof Bell Housing /steel block plate, SFI Billet Fly Wheel, SFI McLeod RST Twin Disc Clutch. Vintage Mr. Gasket Vertigate inline 4 Speed Shifter (rebuilt), Hurst Roll Control “Line-Locâ€.
Scaled weight with 205 lb driver = 1840lbs front / 1760lbs rear / 3490lbs curb total, and balance is 51.8% front / 48.2% rear.
Global West Upper and Lower Front Control Arms, QA1 double adjustable coil over shocks, 1.25" front sway bar (removed).
RedHead Steering Gear restored 1970 Manual steering box.
UMI Adjustable Upper and Lower rear control arms, Flaming River double adjustable rear shocks, MOOG 5401 rear shocks, HRParts-N-Stuff Rear Bar. Driveline NW, 3.5†Heavy wall Drive shaft. Coruso Ind. Driveshaft Safety Loop.
Taylor Battery trunk relocate Box, Moroso Battery Disconnect switch, 0.0 GA Wire.
Heavy Duty 4 core radiator, 7 Blade Thermostatic Clutch Fan, Custom aluminum coolant over flow catch can.
Autometer Sport Comp Oil Pressure Water Temperature and Fuel Pressure Gauges for carb supply and nitrous fuel system supply. Autometer digital programmable tachometer with shift light. Oil pressure and water temperature indicator Pro-Lights. BUICK 1970 Factory in dash tach with Autometer circuitry, AEM Air Fuel Ratio Exhaust sensor and Gauge.
Here is a receipt ledger:
1970 BUICK SKYLARK "STREET SLEEPER" BUILD RECEIPT LEDGER | 9/22/2019 | ||||
GROUP | GROUP DESC. | COMPONENT DESCRIPTION | COST | GROUP TOTAL COST | & OF TOTAL |
A | VEHICLE | 70 Sky Purchase & delivery | $ 800.00 | ||
A | VEHICLE | License & Title | $ 128.25 | ||
A | VEHICLE | 4/21/14 Shine By Design Rub & Wax | $ 175.00 | ||
A | SERVICE | Modern Collision, Tram Gauge Frame -ok | $ 85.00 | $ 1,188.25 | 2.5% |
0 | ENGINE - CLUTCH | 72 BUICK 455 WF CODE Forged 9:1 slugs, crank, assy short block | $ 800.00 | ||
0 | ENGINE - CLUTCH | 72 BUICK 455 WF CODE Dean Kaufman Rebuild & TA Parts | $ 2,000.00 | ||
0 | ENGINE - CLUTCH | 72 BUICK 455 WF CODE Dyno Break-in | $ 550.00 | ||
0 | ENGINE - CLUTCH | TA Stage 1 Street Eliminators - Skaling 340/240 60cc | $ 2,700.00 | ||
0 | ENGINE - CLUTCH | TA 1.6 Roller Rockers | $ 800.00 | ||
0 | ENGINE - CLUTCH | Custom Bullet 228/525x233/525 Cam & Johnson Lifters | $ 385.00 | ||
0 | ENGINE - CLUTCH | ARP Head Bolt Kit | $ 90.00 | ||
0 | ENGINE - CLUTCH | .027" Cometic Head Gaskets | $ 195.00 | ||
0 | ENGINE - CLUTCH | TA 9.375 Moly Push Rods | $ 50.00 | ||
0 | ENGINE - CLUTCH | Summit Heat wrap, oil & temp senders and Header bolts | $ 125.00 | ||
0 | ENGINE - CLUTCH | TPP Oil Dip Stick & tube | $ 65.00 | ||
0 | ENGINE - CLUTCH | AMP Baffle Pan | $ 50.00 | ||
0 | ENGINE - CLUTCH | Intake Grommet for pcv valve | $ 5.00 | ||
0 | ENGINE - CLUTCH | Midwest Muncie M23 4 speed | $ 2,600.00 | ||
0 | ENGINE - CLUTCH | Mr. Gasket Vertigate Shifter and Hurst NOS Boot | $ 1,400.00 | ||
0 | ENGINE - CLUTCH | Lakewood Blow Proof Bellhousing | $ 500.00 | ||
0 | ENGINE - CLUTCH | Holley Recertify Bellhousing & Restore | $ 125.00 | ||
0 | ENGINE - CLUTCH | Wilwood Master Clutch Master Cylinder & Fab Firewall Brkt | $ 84.95 | ||
0 | ENGINE - CLUTCH | Wilwood Aluminum Clutch Fluid Reservoir | $ 99.95 | ||
0 | ENGINE - CLUTCH | Mcleod RST Twin Disc Clutch | $ 703.00 | ||
0 | ENGINE - CLUTCH | Resurface flywheel | $ 50.00 | ||
0 | ENGINE - CLUTCH | American Power Train Hydraulic Throw-out Bearing | $ 380.00 | ||
0 | ENGINE - CLUTCH | #3 straight x #3 90 braided hydraulic line | $ 39.92 | ||
0 | ENGINE - CLUTCH | 3/8x24 #4 male ftg | $ 11.97 | ||
0 | ENGINE - CLUTCH | 7/16x20 male ftg | $ 16.97 | ||
0 | ENGINE - CLUTCH | #4 union | $ 2.97 | ||
0 | ENGINE - CLUTCH | #4 braided line for hydraulic clutch | $ 45.95 | ||
0 | ENGINE - CLUTCH | misc fasteners | $ 115.49 | ||
0 | ENGINE - CLUTCH | Threaded rod parts (3/8) use | $ 15.00 | ||
0 | ENGINE - CLUTCH | Speedo Cable | $ 19.00 | ||
0 | ENGINE - CLUTCH | Replacement speedo cable | $ 20.00 | ||
0 | ENGINE - CLUTCH | 2 qts Trans GL4 fluid | $ 32.00 | ||
0 | ENGINE - CLUTCH | HEIM JOINT & rod | $ 15.00 | ||
0 | ENGINE - CLUTCH | Custom Torque Arm | $ 250.00 | $ 14,342.17 | 30.5% |
1 | COOLING - OILING | 1970 Skylark Grille | $ 125.00 | ||
1 | COOLING - OILING | 7 blade fan and clutch | $ 75.00 | ||
1 | COOLING - OILING | NOS short Water Pump | $ 169.00 | ||
1 | COOLING - OILING | Heater Control Cable blue | $ 25.00 | ||
1 | COOLING - OILING | Radiato, 4 Core restored | $ 400.00 | ||
1 | COOLING - OILING | OEM Replacment Heater Core | $ 60.00 | ||
1 | COOLING - OILING | Heater, Upper, Lower and Bypass Radiator Hoses | $ 65.00 | ||
1 | COOLING - OILING | Alt / PS / Fan Belt (AC Delco) | $ 15.00 | ||
1 | COOLING - OILING | Fan Shroud 1970 TPP Repop | $ 175.00 | ||
1 | COOLING - OILING | Aluminum Overflow Catch Can | $ 50.00 | ||
1 | COOLING - OILING | 4 Core Radiator Rubber Insulators | $ 35.00 | ||
1 | COOLING - OILING | NOS Kenn- Bell Valve Covers & Hardware | $ 530.00 | ||
1 | COOLING - OILING | 180* T Stat | $ 14.00 | $ 1,738.00 | 3.7% |
2 | ELECTRICAL | Wire Harnesses low mile 1970 GS 455 donor - Under Dash & Engine Compartment | $ 150.00 | ||
2 | ELECTRICAL | Rear Defogger - Lat 69/early 70 only (replaced stolen unit) | $ 150.00 | ||
2 | ELECTRICAL | MSD ProBillet Dist & Wires | $ 550.00 | ||
2 | ELECTRICAL | MSD Dist Cap & Rotor | $ 40.00 | ||
2 | ELECTRICAL | MSD Dist Phase Rotor | $ 40.00 | ||
2 | ELECTRICAL | MSD Blaster 3 Coil & Rev Limiter Chips | $ 75.00 | ||
2 | ELECTRICAL | NGK spark plugs | $ 22.00 | ||
2 | ELECTRICAL | Repop Clutch switch wire | $ 29.00 | ||
2 | ELECTRICAL | Omron Clutch switch N2O control | $ 29.00 | ||
2 | ELECTRICAL | Mallory Hyfire VI Programmable Ignition Box | $ 345.00 | ||
2 | ELECTRICAL | Ignition Switch | $ 18.00 | ||
2 | ELECTRICAL | Head Lamps 2 LOW-HI / 2 HI | $ 50.00 | ||
2 | ELECTRICAL | Taylor Trunk Battery Box | $ 65.00 | ||
2 | ELECTRICAL | Mallory 74102 External Battery Disconnect switch & Cables | $ 99.00 | ||
2 | ELECTRICAL | MSD 8984 Starter Saver | $ 121.50 | ||
2 | ELECTRICAL | Ground strap kit | $ 25.00 | ||
2 | ELECTRICAL | Mr. Gasket Plug Wire Looms | $ 45.00 | ||
2 | ELECTRICAL | Tail Light resto & new gaskets | $ 14.00 | ||
2 | ELECTRICAL | Horn Contact Pin | $ 10.00 | ||
2 | ELECTRICAL | Battery- NAPA Gold | $ 124.83 | ||
2 | ELECTRICAL | Backup light switch | $ 30.00 | ||
2 | ELECTRICAL | dome light housing & lens | $ 20.00 | ||
2 | ELECTRICAL | 00 rewire battery & alternator | $ 89.00 | ||
2 | ELECTRICAL | LED exterior lamps and interior lamps | $ 140.00 | ||
2 | ELECTRICAL | Powermaster 9511 Starter | $ 210.00 | ||
2 | ELECTRICAL | Powermaster 150Amp one Wire Alt 47293 | $ 153.00 | ||
2 | ELECTRICAL | American Auto Wire Rear Tail light Harness | $ 149.00 | $ 2,793.33 | 5.9% |
3 | FUEL - EXHAUST | Proform 950 Carb | $ 500.00 | ||
3 | FUEL - EXHAUST | ROB MC FUEL 1100 PUMP, Regulator, 1/2" Tank Pickup,40&100 Micron filters, Braided Lines, AN Fittings, etc. | $ 1,606.00 | ||
3 | FUEL - EXHAUST | 2" Carb spacer Tapered Wilson Style | $ 56.00 | ||
3 | FUEL - EXHAUST | Intake Gaskets .015, .032,.0047 | $ 63.00 | ||
3 | FUEL - EXHAUST | Throttle Cable BBB (NOS) | $ 40.00 | ||
3 | FUEL - EXHAUST | Throttle Cable Bracket CVR Billet Aluminum | $ 99.00 | ||
3 | FUEL - EXHAUST | Max Adj Comp Cams Air bleeds, Jets, etc., assortment- kit & tools | $ 138.90 | ||
3 | FUEL - EXHAUST | #4 Fuel VR set up, shut off & AN fittings | $ 177.00 | ||
3 | FUEL - EXHAUST | Misc fittings to complete fuel system | $ 215.00 | ||
3 | FUEL - EXHAUST | K&N Open Element Air Cleaner Assy 3" | $ 163.00 | ||
3 | FUEL - EXHAUST | K&N Open Element Air filter 4" | $ 45.00 | ||
3 | FUEL - EXHAUST | Gas Tank OEM Donor 1970 | $ 75.00 | ||
3 | FUEL - EXHAUST | 1970 GM A-Body Gas Tank Vent Tube Filter With Hoses, Set | $ 5.00 | ||
3 | FUEL - EXHAUST | Gas Cap | $ 10.00 | ||
3 | FUEL - EXHAUST | Nitrous Supply N2O parts | $ 435.00 | ||
3 | FUEL - EXHAUST | Nitrous Oxide Installation Accys | $ 150.00 | ||
3 | FUEL - EXHAUST | Nitrous Supply - relief valve caps | $ 30.00 | ||
3 | FUEL - EXHAUST | Nitrous Oxide kit Bottle Fill Set Up | $ 75.00 | ||
3 | FUEL - EXHAUST | Nitrous Oxide second bottle adapter and gauge | $ 55.00 | ||
3 | FUEL - EXHAUST | NEX 10 lb. bottle N2O Bottle and gauge #1 | $ 150.00 | ||
3 | FUEL - EXHAUST | NEX 10 lb. bottle N2O Bottle and gauge #2 | $ 150.00 | ||
3 | FUEL - EXHAUST | Nitrous Supply Purge Kit | $ 130.00 | ||
3 | FUEL - EXHAUST | Nitrous Supply plate fogger | $ 130.00 | ||
3 | FUEL - EXHAUST | Nitrous supply jets | $ 60.00 | ||
3 | FUEL - EXHAUST | 1 gal RCI fuel cell fro N2O System | $ 99.00 | ||
3 | FUEL - EXHAUST | In line Secondary Fuel pressure regulator with gauge | $ 80.66 | ||
3 | FUEL - EXHAUST | N2O Bottle Brackets - NHRA Certified | $ 40.00 | ||
3 | FUEL - EXHAUST | Torque Tech DUAL EXHAUST SYSTEM & TAIL PIPES | $ 470.60 | ||
3 | FUEL - EXHAUST | WALKER 20" MUFFLERS | $ 178.30 | ||
3 | FUEL - EXHAUST | MIDAS Weld up fitment | $ 134.00 | ||
3 | FUEL - EXHAUST | 2-1/2" crossover X exhaust kit | $ 185.00 | ||
3 | FUEL - EXHAUST | MIDAS install 2-1/2" crossover X exhaust kit | $ 211.31 | ||
3 | FUEL - EXHAUST | Napa 2-5" Exhaust Sleeve Style Clamps | $ 95.56 | ||
3 | FUEL - EXHAUST | Doug's Headers Jet Hot Coated | $ 575.00 | ||
3 | FUEL - EXHAUST | Meinike cut and bend pipes | $ 120.00 | $ 6,747.33 | 14.3% |
4.5 | BRAKE CONTROL | Brake Master Cylinder and Power Vac Booster Parts | $ 115.00 | ||
4.5 | BRAKE CONTROL | Brake Pedal Retainer Pin | $ 2.50 | ||
4.5 | BRAKE CONTROL | Front Brake Hoses | $ 25.04 | ||
4.5 | BRAKE CONTROL | Rear Drums, Pads, Wheel Cylinders, parts | $ 49.00 | ||
4.5 | BRAKE CONTROL | Bleed, Flush, Fluid - Les Schwab | $ 55.00 | ||
4.5 | BRAKE CONTROL | Front Wheel Cylinders | $ 17.68 | ||
4.5 | BRAKE CONTROL | Hurst Line Lock / Roll Control kit | $ 155.60 | ||
4.5 | BRAKE CONTROL | Hurst Line Lock / Roll Control kit Shift T Handle | $ 57.06 | $ 476.88 | 1.0% |
5 | BRAKE OPERATING REAR AXLE | Quick Performance 3.7 posi, 31 spline, Locker | $ 2,455.00 | ||
5 | BRAKE OPERATING REAR AXLE | Under Dash OEM Donor Pedal Pedestal M/T | $ 25.00 | ||
5 | BRAKE OPERATING REAR AXLE | Drive Shaft NW Drivelines -3.75" HD Tube | $ 367.00 | ||
5 | BRAKE OPERATING REAR AXLE | Driveline NW Ujoint conversion for 9" | $ 78.00 | ||
5 | BRAKE OPERATING REAR AXLE | F41 Braces (OEM) | $ 50.00 | ||
5 | BRAKE OPERATING REAR AXLE | Drive Shaft Safety Loop Corusso Ind | $ 92.00 | ||
5 | BRAKE OPERATING REAR AXLE | Street Wheels - Front - OEM GM 15" x 7" Steelies, blasted & powder coated | $ 306.00 | ||
5 | BRAKE OPERATING REAR AXLE | Street Tires - Front - BFG Radial T/A 245/60/15 | $ 360.00 | ||
5 | BRAKE OPERATING REAR AXLE | Street Wheels - Rear - Speedway 15 x 8 GM Steel Wheels (Five ea. powder coated) | $ 200.00 | ||
5 | BRAKE OPERATING REAR AXLE | Street Tires - Rear -Mickey Thompson ET Street Radial 275 / 60 /15 | $ 440.00 | ||
5 | BRAKE OPERATING REAR AXLE | Mount & Balance | $ 45.00 | ||
5 | BRAKE OPERATING REAR AXLE | Dog Dish Caps - Set of Four Driver Quality | $ 150.00 | ||
5 | BRAKE OPERATING REAR AXLE | Drag Wheels - Vintage Cragar Super Trick Aluminum 15" x 10" & 15" x 4" wheels | $ 820.00 | ||
5 | BRAKE OPERATING REAR AXLE | Drag Tires - Front - Mickey Thompson 15" x 4-1/2" front drags | $ 360.00 | ||
5 | BRAKE OPERATING REAR AXLE | Drag Tires - Rear - Mickey Thompson Drag ET Slicks 90000022010, tubed and screwed | $ 521.00 | ||
5 | BRAKE OPERATING REAR AXLE | Mount & Balance | $ 90.00 | $ 6,359.00 | 13.5% |
6 | FRONT SUSPENSION - STEERING | 15" Blue Sport Steering Wheel | $ 215.00 | ||
6 | FRONT SUSPENSION - STEERING | Steering Column M/T OEM Donor - Restored | $ 190.00 | ||
6 | FRONT SUSPENSION - STEERING | Front End Alignment- Les Schwab | $ 60.00 | ||
6 | FRONT SUSPENSION - STEERING | 1979 Pontiac Firebird 1.25" OEM front sway bar | $ 100.00 | ||
6 | FRONT SUSPENSION - STEERING | Energy Suspension 1.25" sway bar bushing | $ 16.00 | ||
6 | FRONT SUSPENSION - STEERING | Moog Rear 5501 Springs | $ 100.00 | ||
6 | FRONT SUSPENSION - STEERING | UMI Rear Adjustable upper / non adj. lower control arms | $ 375.00 | ||
6 | FRONT SUSPENSION - STEERING | Flaming River 2X Adjustable rear Shocks | $ 260.00 | ||
6 | FRONT SUSPENSION - STEERING | QA1 2X Adjustable front Coil Over & GW Upper & Lower Arm | $ 1,996.45 | ||
6 | FRONT SUSPENSION - STEERING | HRPartsNStuff rear bar | $ 450.00 | ||
6 | FRONT SUSPENSION - STEERING | 2nd Front end Alignment | $ 66.00 | ||
6 | FRONT SUSPENSION - STEERING | Red head Steering Gear Rebuild Manual Steering Box & Box | $ 464.62 | $ 4,293.07 | 9.1% |
7 | SPRINGS- BUMPERS | Remove Body, Blast and Restore Frame painted gloss black | $ 150.00 | ||
7 | SPRINGS- BUMPERS | 455 Frame Mounts | $ 100.00 | ||
7 | SPRINGS- BUMPERS | Body Bushing Kit | $ 125.00 | ||
7 | SPRINGS- BUMPERS | Straighten Bumper - Art Brass, Seattle, WA | $ 175.00 | ||
7 | SPRINGS- BUMPERS | Cross Member | $ 30.00 | ||
7 | SPRINGS- BUMPERS | Front Bumper Rubber Filler | $ 10.00 | ||
7 | SPRINGS- BUMPERS | Trunk Jack Assy - plus restoration | $ 75.00 | $ 665.00 | 1.4% |
8 | SHEET METAL - HEATER | Under Hood Insulation Kit | $ 22.00 | ||
8 | SHEET METAL - HEATER | Firewall Insulation Kit | $ 50.00 | ||
8 | SHEET METAL - HEATER | Heater Core Restore Box | $ 26.00 | $ 98.00 | 0.2% |
9 | INSTRUMENTS - MISC | OEM Radio Delete Plate | $ 100.00 | ||
9 | INSTRUMENTS - MISC | Antenna Pigtail | $ 25.00 | ||
9 | INSTRUMENTS - MISC | M/T Speedo | $ 200.00 | ||
9 | INSTRUMENTS - MISC | Factory Dash Tach & restoration | $ 400.00 | ||
9 | INSTRUMENTS - MISC | Factory Rally Gauges | $ 50.00 | ||
9 | INSTRUMENTS - MISC | Seat Belts 1970 OEM Donor | $ 250.00 | ||
9 | INSTRUMENTS - MISC | Autometer ProComp Oil & Water Gauges w/ Cups | $ 250.00 | ||
9 | INSTRUMENTS - MISC | Autometer Air Fuel Ratio Meter | $ 160.00 | ||
9 | INSTRUMENTS - MISC | AEM Air Fuel ratio Gauge w/ cup | $ 200.00 | ||
9 | INSTRUMENTS - MISC | Autometer Level 1 Cobalt Digital Pro Shift Light Tach 6187 w/cup | $ 230.00 | ||
9 | INSTRUMENTS - MISC | Autometer Comp Pro Fuel Pressure Gauge w/ cup | $ 257.67 | ||
9 | INSTRUMENTS - MISC | TD Fuel Pressure Gauge, mount & braided line | $ 304.44 | ||
9 | INSTRUMENTS - MISC | Customized N2O switch panel radio delete | $ 55.00 | ||
9 | INSTRUMENTS - MISC | IH hour meter | $ 15.00 | $ 2,497.11 | 5.3% |
10 | DOORS HARDWARE -GLASS | Front Windshield | $ 150.00 | ||
10 | DOORS HARDWARE -GLASS | Weather Seals Sof Seal A Body Kit complete | $ 150.00 | ||
10 | DOORS HARDWARE -GLASS | Washer Tank | $ 25.00 | ||
10 | DOORS HARDWARE -GLASS | Inner Fender A Frame Seals | $ 12.00 | ||
10 | DOORS HARDWARE -GLASS | Washer Pump & Assembly, Restored | $ 50.00 | ||
10 | DOORS HARDWARE -GLASS | Cranks & Knobs | $ 25.00 | ||
10 | DOORS HARDWARE -GLASS | Washer Screws | $ 5.00 | ||
10 | DOORS HARDWARE -GLASS | Door Hinge Dr Side | $ 15.00 | ||
10 | DOORS HARDWARE -GLASS | Door Edge Guards OEM Stainless | $ 25.00 | ||
10 | DOORS HARDWARE -GLASS | Door Locks | $ 12.00 | ||
10 | DOORS HARDWARE -GLASS | Door Locks & Handle Gasket Kit | $ 6.00 | ||
10 | DOORS HARDWARE -GLASS | Trunk Lock & Key alike to Glove Box | $ 10.00 | ||
10 | DOORS HARDWARE -GLASS | Glove Box lock - key alike to Trunk Lock | $ 25.00 | ||
10 | DOORS HARDWARE -GLASS | Wiper Blades | $ 15.00 | ||
10 | DOORS HARDWARE -GLASS | Sport Mirrors | $ 85.00 | ||
10 | DOORS HARDWARE -GLASS | Sport Mirror replacement glass | $ 46.00 | ||
10 | DOORS HARDWARE -GLASS | Map Light rear view mirror | $ 45.00 | ||
10 | DOORS HARDWARE -GLASS | Windshield Washer Hoses | $ 2.50 | ||
10 | DOORS HARDWARE -GLASS | Outer door fuzzies | $ 100.00 | $ 803.50 | 1.7% |
12 | BODY MOLDING - SHEET METAL | Hurst Equipped Trunk Emblem | $ 20.00 | ||
12 | BODY MOLDING - SHEET METAL | Hood Pins | $ 25.00 | ||
12 | BODY MOLDING - SHEET METAL | Rubber Bumpers- Trunk | $ 5.50 | ||
12 | BODY MOLDING - SHEET METAL | Sandblast work Inner fenders, core support, cross member | $ 300.00 | ||
12 | BODY MOLDING - SHEET METAL | Core Support Repair kit | $ 120.00 | ||
12 | BODY MOLDING - SHEET METAL | Inner Fender Repair kit | $ 65.00 | ||
12 | BODY MOLDING - SHEET METAL | RUST PREP & RESURFACE INC PRODUCTS & COATINGS floors | $ 50.00 | ||
12 | BODY MOLDING - SHEET METAL | RUST PREP & RESURFACE INC PRODUCTS & COATINGS Trunk | $ 25.00 | ||
12 | BODY MOLDING - SHEET METAL | Battery Tray & Clamp | $ 50.00 | ||
12 | BODY MOLDING - SHEET METAL | Cage Nuts & Core Spt Clips | $ 25.00 | ||
12 | BODY MOLDING - SHEET METAL | Body Side Moldings 1970 Only replaced original OEM Donor | $ 70.00 | ||
12 | BODY MOLDING - SHEET METAL | Outer Fender Well Dust Shields | $ 15.00 | ||
12 | BODY MOLDING - SHEET METAL | Hood release Handle 1970 only | $ 10.00 | ||
12 | BODY MOLDING - SHEET METAL | 70 Rocker Moldings | $ 150.00 | ||
12 | BODY MOLDING - SHEET METAL | 70 Rocker Molding Hardware Kit | $ 42.00 | ||
12 | BODY MOLDING - SHEET METAL | 70 Lower Quarter Rocker Moldings | $ 75.00 | ||
12 | BODY MOLDING - SHEET METAL | Quarter panel extension gaskets | $ 10.00 | ||
12 | BODY MOLDING - SHEET METAL | Bumper filler - passenger side | $ 5.00 | ||
12 | BODY MOLDING - SHEET METAL | Fire wall plug | $ 5.00 | ||
12 | BODY MOLDING - SHEET METAL | Fabricate steel custom floor hump for Vgate shifter | $ 25.00 | ||
12 | BODY MOLDING - SHEET METAL | Kenne Bell Stage 2 hood Scoop | $ 120.00 | $ 1,212.50 | 2.6% |
15 | TRIM - CARPETS - MATS | PUI Front & Rear Set covers | $ 638.00 | ||
15 | TRIM - CARPETS - MATS | Rich's rebuild seats | $ 1,924.00 | ||
15 | TRIM - CARPETS - MATS | A Pillar Trim | $ 20.00 | ||
15 | TRIM - CARPETS - MATS | Package Tray Plastic Corners | $ 20.00 | ||
15 | TRIM - CARPETS - MATS | Interior Metal Restoration / Paint | $ 30.00 | ||
15 | TRIM - CARPETS - MATS | Interior Vinyl / Plastic Restoration / Paint | $ 30.00 | ||
15 | TRIM - CARPETS - MATS | Carpet Kit | $ 151.10 | ||
15 | TRIM - CARPETS - MATS | Carpet Felt Jute | $ 20.50 | ||
15 | TRIM - CARPETS - MATS | Door Panel Work carpet lower | $ 80.00 | ||
15 | TRIM - CARPETS - MATS | Door Panel PUI Staonless spears lower door panel to carpet transition | $ 80.00 | ||
15 | TRIM - CARPETS - MATS | Restore Kick Panels | $ 9.00 | ||
15 | TRIM - CARPETS - MATS | Package Tray w/ jute pad | $ 74.10 | ||
15 | TRIM - CARPETS - MATS | Glove Box Liner | $ 29.00 | ||
15 | TRIM - CARPETS - MATS | Door Lock Knobs | $ 6.00 | ||
15 | TRIM - CARPETS - MATS | Jack Instruction decal | $ 6.00 | $ 3,117.70 | 6.6% |
MISC | MISC | GSX DASH EMBLEM & SKYLARK QTR PANEL SCRIPTS | $ 90.00 | ||
MISC | MISC | MISC CLEANER, FASTENERS, PAINT,ETC | $ 262.56 | ||
MISC | MISC | Alum floor jack | $ 248.00 | ||
MISC | MISC | 5 RCI Fuel Jugs | $ 135.00 | $ 735.56 | 1.6% |
TOTAL TO DATE | $ 47,067.40 | $ 47,067.40 | 100.0% |
Here is a video walk around https://www.youtube.com/watch?v=_lVdAXGNJ4A
On Oct-05-19 at 06:26:04 PDT, seller added the following information:Try this Youtube link https://youtu.be/_lVdAXGNJ4A