1972 Datsun 1200 SR20 FuelTech Sedan White RWD Manual

1972 Datsun 1200 SR20 FuelTech for sale

Make: Datsun
Model: 1200 SR20 FuelTech
Type: Sedan
Year: 1972
Mileage: 9999999
VIN: LB110369633
Color: White
Engine size: SR20
Number of cylinders: 4
Fuel: Gasoline
Transmission: Manual
Drive type: RWD
Vehicle Title: Clean
Want to buy? Contact seller!

Description for Datsun 1200 SR20 FuelTech 1972

Vehicle Details

10% will be donated to St. Jude Research Children’s Hopital.

It’s the right thing to do and paying it forward works for me .

Datsun 1200 sedan . Original California Car. Very solid 99 percent rust free. The trim on car is available it’s just not on . Grill, bumpers, lights, headlight surrounds are all original and will go with the car. ( I have more pics if interested)

This is a project car with a JDM FWD SR20 converted to RWD with a s13 5 speed transmission ( custom Tranny Mount Megan Racing. )

This motor was bought from Toyota1515 MR Castillo he can vouch for it

Custom made crossmember with customized one of a kind set of bracket mounts. Uses 1970s Dodge Van Motor Mounts . Racing clutch and pressure plate.

Complete wire tuck with sealed smoothed out firewall. Battery cables running from the rear or car.

Reversed mount Racing Wilwood brake master cylinder mounted with custom made brackets.

Engine has custom made header, Toyota 4ag ITB with a custom intake to suit the engine . All injectors and fuel rail with braided hoses and swivel fittings.

Motor has been installed along with mated transmission and a custom driveshaft that converts S13 to Datsun Rear End.

Rear end comes from a 67 Datsun Roadster that has been retrofitted to the car using the original shock mount, which are welded to it .

Wired for a FuelTech FT350 that will be included in sale.

The car has been stripped of original wiring and has been customized with the FuelTech wiring which is 80 percent wired to the motor except the crank trigger wheel. It is setup to run on Crank shaft signal

CAM sensor has been eliminated since motor was FWD and would not fit without cutting into the firewall

All other sensors are installe, wired and tested to run the FuelTech. 3 row aluminum radiator, oil cooler in black and red. Braided Hi Pressure Fuel lines from fuel rail to the rear end. Needs finishing to connect to tank.

Custom Relay box with surge protectors and upgraded fuses. Lights are wired but need finishing .

Interior is stripped . I have a RHD dashboard along with the original which is pretty shot

The dashboard has to be re fabricated.

I have the seats in black but they might need some repairs. Momo wheel adapter

Fuel tank is stock and has Bosch type inline fuel pump inside a secondary smaller fuel cell .

Secondary low pressure fuel pump as well is included. Fuel lines need to be finished and installed to finish the fuel tank plumbing

Brake lines need to be installed which will work in conjunction with a hydro e brake that is included as well as 4 new Wilwood 4 piston calipers and customized brackets .

2 inch straight pipe with a mid sound muffler

Emergency power cut off switch .

Car will no longer accept 12 inch wheels as they will interfere with calipers

4 new 15x 7 wheels with new tires in rear . Front wheels need tires.

Suspension in front has camber plates and strut towers were customized to get more negative camber. New VW Golf front strut inserts need to be cut to fit the struts, as it runs shorter than stock strut.

Rear disks need to be retrofitted to eliminate the brake drum system . Needs additional front disk brakes for the front .

Hubs are customized to fit 240SX bolt pattern

Car will need done additional work to finish

I know it looks like a headache but once done it will be an amazing build.

I will help with how to deal with thi, perhaps maybe just the shell.

None the less this is sought after vehicle and it’s hard to find a solid sedan .

Needs:

plumbing work / cooling

Interior and dash finished

Installation of fuel pump lines as those are regular non hi pressure

Installing brake system and plumbing

Install a crank trigger wheel mount. 60-2 trigger wheel installed.

Vacuum system which needs to be fabricated.

Trunk refinishing

Needs front There is more that I have prolly forgot but if there are any questions don’t hesitate to contact .

All sales final .

A non refundable deposit of $1000 due no later than 48 hours of winning .

Only accept valid forms of payment.

Buyer responsible for all shipping arrangements and costs .

Seller has no responsibility for all of these costs and arrangements.

Thank you and God bless

Other classic cars for sale