1969 Ford F-100 Fully Custom Resto-Mod Best Interior Award Winner LOOK WOW!

Description for Ford F-100 1969

On Jan-10-18 at 20:18:42 PST, seller added the following information:

• power brakes
• beltech lowering arms
• dual flowmaster exhaust
• clear texas title in my name

On Jan-14-18 at 06:38:05 PST, seller added the following information:

vin number is incorrect in listing I put my 1970 ford crew cab Vin on accident so here is correct VIN: F10AKF12293
New in April and May 2017:

• new aeromotive fuel filter $135
• new aeromotive high pressure aluminum fuel tank to support the fuel injection Fitech system. $672
• New Nylon Race Hose - $132
• new black nylon race hose - $135
• Fi -Tech Fuel Injection plus controller - $2500
• Strip Engine Prep for High Performance rebuild plus labor - under warranty - $1,387
• BBK Shorty Headers - $300
• Aluminum Finned Oil Pan - $90
• 15 inch full finned air cleaner and assymbly - $309
• Valve cover classic Ford - $225
• oil pan gasket - $34
• valve cover gasket $26
• new header gasket - $38

• New Power Torque - $15
• New roadmaster water pumps, oil and grease seal - $37
• New F/P plate - $10
• New PCV Valve, fuelline hose EEC primary wire - $11
• Installation of new oil sending unit, wire up coil, and FiTech Tach, install and run wire and in cab handheld controller, lengthen coil wires, re-fit oil cover wires.
• fix body guard, cut hole custom in bed for gas door, mock and make heavy duty ground wires frame to body then engine to frame, test starter begin to mackup throttle linkage. $693
• All new Amsoil 10w30 oilchange - $65
• NEW oil filter - $12
• Install radiator, wire ac and FiTech line and cover, make throttle linkage from kit, modify bracket, set up FiTech Fuel injection system - $675
• Smileys SRP AN fittings - $51
• WCH Racing Engines, build performance engine intake to oil pan, file fit rings, poilsh crankshaft bore/hone/clean/check or replace valve springs assemble. Engine Kit, Timing Cover, Rod Bolts, Push Rods, Roller Rockers, Roller Cam Shaft, Roller Lifters, Oil Penn SAE 30 Break in, Plugs NGK, Six Filter, ARP HEAD BOLTS, Timing Tab, MSD ignition, gear for Roller. - $3,481
• Drill holes in valve covers for breathers, install valve covers, check flex plate clearence, drain fluid, R&I OIL PAN, Install engine, measure and remove to install mid plate, re-install, put on motor mounts. - $1106
• Torque Converter Bolts, inspect underside of truck cables, mock up to reuse front runner, tap install water pump and front runner - $600
• Complete water pump install, install and test front runner belt alignment, re adjust until correct. - $525
• get truck on lift weld 02 bung, undo exhaust exhaust hangers on passenger side to weld all -n bung, remove old ink, cut rear exhaust off to clear new tank, cut frame rails and clean up cut, begin marking rear gas tank mount, remove bed, remove rear cross member, steel nut seat side for tank - $600
• Gas Tank Crossmember, paint, gas tank front spacer, paint, install tank - $656
• Summit Racing Steering Column- $502
• Set FiTech EFI Unit on intake, Install AN fittings, run fuel line and fittings vent, make 2 ground wires, R&I HEADER RIGHT SIDE ENLARGE FLANGE HOLES, enlarge left side flange, remove old fuel lines - $750

On Jan-14-18 at 07:03:20 PST, seller added the following information:

NEW MAY/JUNE Continued:

Summit Racing invoice: fuel filter, filter clamp,
hose end AN-06 - $179

Labor 9.75 Mount fuel filter, run and wire for fuel pump,
bolt header flanges, realign front runner
system and line it up, connect fuel pump, Fi-Tech hot lead and 16N, rerun fuel pumppower and hide wires - $731

Labor 9.50 Safety wrap & tie wires and fuel lines, install
starter, install speedo gear, wrap rear fuel
wires, set and align bed, measure for gasdoor install thermostat and hoses, begin Fi- Tech tuning - $712

Part 1 Roadmaster invoice: WTR outlet gasket,
fittings, coolant hose (molded), thermostat,
hose clamp, resistor - $43

Part 1 Summit Racing invoice: fuel door - $96

May June Total invoices - $6509.15

Invoice 1273

NEW E-Street Cyl Heads SBF - $928

Manifold Performer RPM SBF Intake Manifolds - $265

Bolt Kit Intake Manifold -$28

Shipping - $35

Invoice 1310

Part 1 Exxon invoice: fuel - $11

Part 1 Fastenal invoice: socket cap screw - $9

Part 1 Smileys Invoice: SRP throttle linkage kit, rods,
ends, and springs - $27

Part 1 Roadmaster invoice: amber global ext life anti
freeze - $50

Labor 7 R&I coil, ballast resistor, tighten, troubleshoot,
fabricate gas door base - $525

Labor 9 Finish fab on gas door, pull dash hook up,
speedometer wiring, test, add trans flui,
mount gas door, mock, paint gas door spacer,align bed, secured battery box, tuck wires - $675

Part 2 AMSOIL: trans fluid -$25

Labor 4.75 Bolt bed, test drive, adjust detent cable, add
spring, mock dipstick $356

Part 1 Roadmaster invoice: oil dipstick - $12

Labor 4 Torque water pump, remove steering column,
mock new column, remove leather from
column - $300

Services 1 Teo Upholstery invoice: steering wheel wrap - $50

Labor 10.75 Column lower mount, install hood and adjust,
work on column wiring, adapt wiring harness
on steering column install, drill firewall plates,test drive, fuel - $806

Labor 4.75 Road test and tune, work on temp gauge,
drain anti freeze and R&I sensor, change
temp sensor - $356

Test drive and quality check, clean up, prep
for delivery

REBUILT AUTOMATIC OVERDRIVE TRANSMISSION WITH NEW TORQUE CONVERTER AND JUNIOR SHIFT KIT OCTOBER 19 2017 WITH SIX MONTH WARRANTY!

NEW 225/70/15 Cooper white letter tires with 50,000 mile warranty from discount tire - $198 12-5-16

2016 interior build:

Truck got same material mercedes benz uses for thick padded foam dampening throughout cab beneath the crosshatch leather headliner, floorboard, seats walls and cab for professional sound dampening. New custom adjustable bucket seats, custom built center console, cup holders, and shifter column, leather wrapped entire inside of cab and cutom install/design. Install new vintage gauges. Wire up blinkers and horn. Install defrost vents and shotgun shell door locks - $6050

On Jan-14-18 at 20:33:22 PST, seller added the following information:

HAPPY BIDDING, BID HIGH AND FAST TO ENSURE YOU ARE THE WINNING BIDDER. VIDEO OF THE TRUCK STARTING DRIVING AND IDLING UPON MESSAGE REQUEST. ANY QUESTIONS PLEASE FEEL FREE TO MESSAGE ME.