Road Race Fox Mustang Wide Body

Description for Ford Mustang 1989

1989 Ford Mustang Wide Body

The perfect street legal track day car. I am the original owner. Purchased new in April 1989 and have taken expert care of my Mustang for 26 years. Daily driver originally then complete overhaul of entire car in 2010 tocomparable American Iron Series Mustangs. The only original equipment left on car is floor pan and doors. Built for severe track duty. One of a kind Maier Racingwide body Fox Mustang. Super wide wheel/tire combo. 315/30/18 tires at all four corners! Looks like no other Mustang I have ever seen. Handles like a race car with every suspension pieceMaximum Motorsports offers. Near show car build quality. Immaculate exterior. No rust. Hatchback. Bullet proof mechanicals. The naturally aspirated" big bore" 347 cubic inch motor pulls hard to 6,500 rpm with an engine and exhaust note that gives this car quite a presence. Every aspect of rebuild purposefully chosen to maximize track performance and minimize weight. Designed for open track days at Pittsburgh International raceway track. As a group 3 driver, y Mustang got around the track as quickly or quicker than any exotic European or domestic sports car. Still streetable but at home on open road race track. Drive it to the track, un it hard, hen drive it home. Safe, eliable track day car. Asking price: $30,000. I will deliver car. Total restoration details:

Body

Engine

1.Ford Racing Boss block with 4 bolt mains, ored to 4.125" and stroked to 3.25". A 347 cubic inch "big bore"motor. Preferable rod to stroke ratio than standard 347 stroker. Great power band that keeps on pulling when coming out of bends.

2.Diamond custom aluminum pistons with graphite coated side skirts to minimize friction and heat

3.Eagle micropolished forged crankshaft

4.Eagle H-beams rods

5.ATI "super damper" harmonic balancer

6.Canton 7quart road race oil pan and windage tray. Fresh Brad Penn "Green Racing oil"

7.Custom Cams camshaft good for 6,500 rpm shifts. Selected by Fox Lake Racing to maximize power of their cylinder heads

8.Fox Lake Racing custom CNC ported Edelbrock heads with stainless steel Manley valves and dual high rev springs and titanium retainers, ecured with ARP rocker studs and guide plates. Flows 300 cfm of air at .600 lift. Secured with Cometic head gaskets

9.Comp Ultra gold aluminum roller rockers. Light and strong.

10.Holley Systemax EFI upper intake manifold with Fox Lake stage 2 porting for much increased air flow

11.Holley Systemax lower intake manifold custom port matched by Fox Lake for maximum flow

12.Accufab polished big 90mm throttle body with blank EGR spacer

13.Chicane Racing "Fox Box" cold air intake with 90mm mass air sensor. Draws cold air from inside front fender, ot engine bay. True cold air intake.

14.Ford Racing black raised valve covers with raised plenum

15.Edelbrock polished high flow aluminum water pump and high flow polished water neck

16.Griffin high performance 2" aluminum radiator with custom shroud and dual fans with built in oil cooler, anually operated from cockpit and filled with BeCool coolant. Massive air cooling. Can run fans with engine off between lap sessions to cool motor

17.aluminum coolant hoses

18.Canton overflow coolant catch can

19.Pa performance mini starter

20.Pa performance black alternator

21.March high performance aluminum pulleys. Smog pump removed. Shorter belt for less parasitic engine loss.

22.Performance distributors "hot forged" DUI distributor

23.Optima red top battery in Steeda battery box mounted in hatch for better weight distribution

24.MSD ignition coil

25.MSD 6AL-2 ignition box mounted in cab

26.Ford Racing black spark plug wires

27.BBK 1 and 3/4 ceramic coated long tube headers

28.Bassani X pipe with Flowmaster mufflers and Flowmaster 3.5" black exhaust tips

279.Aeromotive fuel rails and lines

30.Glenns Performance aluminum sumped and baffled 18.5 gallon fuel tank with black billet fuel filler door

31.custom dyno tuned at Rodeheaver's Hot Rod Shop

Drivetrain

1.Tremec T-56 "Viper Spec" 6 speed manual transmission. Upgraded bronze fork pads for heavy duty use. SFI approved steel bellhousing. Built by D@D performance with reverse lockout for track use. Reverse lockout controlled from cockpit.

2.Anderson Motorsport aluminum flywheel

3.Pro 5.0 shifter with Tremec shift knob

4.Ford Racing 3.55 gears

5.Torsen T2R differential 31 spline. Really puts the power to the road. Aluminum differential cover for added strength.

6.31 spline Moser 5 lug axle shafts

7.custom aluminum driveshaft from D@D

8.Spec stage 3+ clutch with heavy duty Moroso clutch cable

Steering

1.Maximum Motorsports race power steering pump. Never over heats. New Redline power steering fluid.

2.MM hybrid steering shaft from SN95 Mustang for much improved steering response

3.2003 Mustang Cobra steering rack

4.MM camber/caster plates for ease of custom alignment

5.Momo steering wheel

6.MM tie rod ends

Brakes

1.Ford Racing 1993 Cobra R disc brake kit. front 13" rotors, ear 11.65" rotors and new Hawk HP plus brake pads and brake proportioning valve

2.MM manual brake conversion kit with custom brake pedal for great brake pedal feel on track

3.stainless steel brake lines

4.new Motul brake fluid

Chassis

1.MM full length welded subframe connectors

2.MM 6 point roll cage with bent down door bars for easy access

3.strut tower brace

4.shock tower brace

5.K-member brace

Suspension ( everything Maximum Motorsport offered )

1.MM front and rear coil over kit with MM3 Bilstein Race dampers and hypercoil springs

2.MM tubular K-member

3.MM forward offset and wider track front control arms with Delrin bushings. When combined with K-member front wheel pushed forward 1 and 3/4 inches for better weight distribution

4.MM front sway bar

5.MM adjustable rear sway bar

6.MM rear Torque arm

7.MM rear Panhard bar

8.MM race rear lower control arms

9.CCW 18X11" 3 piece wheels with Nitto NT-01 track tires. 315/30/18 at all four corners!! Lots of grip

Interior

1.Corbeau FX1 Pro fixed back racing seats. Black microseude.

2.Corbeau 5 point harness belts with quick release

3.Autometer Ultralite mechanical gauges ( speedometer, achometer, uel level and voltage meter) in custom Florida 5.0 gauge cluster with carbon fiber background

4.additional mechanical gauges for fuel pressure, il pressure, il temperature and transmission temperature and fuel pressure

5.Painless Power Panel dash switch panel for control of both driver and passenger side radiator fans and reverse lockout

6.floor mounted fire extinguisher

7.billet: door handles, ocks, mergency brake handle and trim around shifter

8.black interior is purposefully sparse but neat and clean. All sound deadening, adio, peakers, arpet and rear seats removed to save weight.