1968 Ford Mustang Hatchback Red RWD Manual Fastback with Chassis Works Chassis

Description for Ford Mustang 1968

Vehicle Details

1968 Mustang Fastback that originally was a 289 with a 3 speed manual transmission. The car is sitting on a complete Chassis Works by Chris Alston Chassis. All information on the chassis is included in the pictures. The rear end is a customized independent 9in Rear End. We decided to go a different direction with a project which is why this is up for sale. The original engine and transmission are not included.

Chassis Information

g-Street Rocker IRS Chassis 64-70 Mustang Contains: Welded A-Arm

& Rocker IRS Frame, Engine and Transmission Chassis Mounts, Inner

Rocker Panels, Seat Platform Tunnel Transition, Front Firewall,

Complete Floor Behind Firewall with Transmission & Driveshaft

Tunnels, Wheel Tubs & Package Tray Bulkhead, Accepts g-Machine or

Pro-Billet Upright Front Suspension, Coil-Over Rocker-Arm IRS with

Splined Antiroll Bar Rear Suspension. Front Frame Outside Width 32"

With Rear Frame Outside Width 35", Optional Roll Bar or Cage.

PALLET 2 WAY68 x 36 HEAT TREATED WOOD, FORK ENTRY ON

36" SIDE ONLY FOR WELDED CLIPS

Build Specs:

36 x 68 Two Way Pallet

3-36 inch long 4 x 4 Stringers

6-68 inch 2 x 4 Decking

Starting from one 68 inch Side. The First 2 x 4 Board is Flush with the

Side, 1" Gap then Second Board, 1" Gap then Third Board, Evenly

Space the Other 3 Boards from there to Evenly Fill up the Remainder of

the 36 length.

MAINHOOP 65-70 FASTBACK MUSTANG DOM 1-3/4 x .125 TILTED

BACK STYLE FOR EXACTFIT CAGE

4872-04-2 EA 1.0000 0.0000 0.0000 COMPONENT

WINDSHIELD BRACE 65-70 MUSTANG DOM 1-3/4 x .125 TILTED

BACK STYLE FOR EXACTFIT CAGE FITS COUPE & FASTBACK

CAGE SIDE DR 65-70 MUSTANG DOM 1-3/4 x .125 THROUGH DASH

FOR EXACTFIT CAGE FITS COUPE & FASTBACK

CAGE SIDE PS 65-70 MUSTANG DOM 1-3/4 x .125 THROUGH DASH

FOR EXACTFIT CAGE FITS COUPE & FASTBACK

Rear Strut Fastback OEM/g-Street Frame DR 65-70 MUSTANG DOM

1-3/4 x .125 Driver Side Follows Roof Thru Package Tray Attaches to

Outrigger on Rear Frame Behind Wheel Tub or Floor in OEM Frame for

Exact Fit Roll Bar & Cage

Rear Strut Fastback OEM/g-Street Frame PS 65-70 MUSTANG DOM

1-3/4 x .125 Passenger Side Follows Roof Thru Package Tray Attaches

to Outrigger on Rear Frame Behind Wheel Tub or Floor in OEM Frame

for Exact Fit Roll Bar & Cage

SIDE BAR DOM 1-3/4 ROLL CAGE 65-70 MUSTANG M/S 1-3/4 x .125

1-BEND FOR EXACTFIT ROLL CAGE FITS BOTH SIDES

Builder Tubs 34 Dia x 21Widex 18 Gauge Steel with 3-1/4" Extra Skin

Length Per Side Past End Cap. Shipped Unassembled for Easier

Installation.

TREMEC T-56 Magnum 6 Speed Mount With Driveshaft Loop & Torque

Arm Mount for 7740-7742-7743 64-70 Mustang g-Street Chassis

FITMENT NOTE:

Fits Aftermarket T-56 MAGNUM Transmissions TUET11009 &

TUET11012 and Others with Crossmember Mount Bolts 26.6 Inches

Behind Back of Engine. Tailshaft Mount Pad is 4.930 Below Centerline.

SWINGOUT CLEVIS & SINGLE EYEBOLT 1-3/4x.134 ROLL CAGES

7044 EACH 1.0000 0.0000 0.0000 COMPONENT

Back Brace gStreet 1-3/4 TubeBolt-In Connection

Hardware 774X-M10 g-Street Chassis 7740-M10, 7741-M10, 7742-M10

& 7743-M10

7950-7740M10F EACH 1.0000 0.0000 0.0000 COMPONENT

Front Floor 4Link/TA/IRS 65-70 Mustang 774X-M10 g-Street Chassis

With 4-Link, Torque-Arm or IRS Rear Suspension. Contains Front Inner

Splash Pans, Complete Floor Behind Firewall Foward of Main Hoop 2x4

Crossmember. With Front Floor, Transmission Tunnel, Seat Platform,

Tunnel Transition, Drive Shaft Cover and Driveshaft Floor.

Rear Floor IRS 64-70 Mustang 7722/7723/7742/7743-M10 g-Street Clip

& Chassis With IRS Rear Suspension. Contains Complete Floor Behind

2x4 Main Hoop Crossmember With Package Tray Bulkhead.

Install Guide 7055-M10 65-70 MUSTANG ExactFit Roll Cage 1-3/4

DOM

Install Guide 7740 Thru 7743-M10 g-Street Full Frame Chassis & Floor

With 4Link, Torque Arm & IRS Rear Suspension For64-70 Mustang

GUSSET A-PILLAR CAGE SIDE gSTREET CHASSIS F-10 & F20 &

M10

Rear IRS Rocker Clip Low g-Street Ground Clearance M10 Chasssis

Low Ride Height 35" Wide 4 x 2 Clip 64-70 Mustang GEN2

Rocker Wireway Assembly DR g-Street Chassis M10

Rocker Wireway Assembly PS g-Street Chassis M10

Front Clip V8 Ford g-Street 64-70 Mustang Includes SB/BB Ford Engine

Frame Horns & Center 2x4 Frame Rails With Splined ARB Mounts

Measuring Tab Front Bumper Mount M10 Clip g-Street Chassis

TUBE 1-1/4 x .120 DOM x 60.000 INCHES LONG +or- .050 YIELD IS 4

PIECES PER 20 FOOT LENGTH

TUBE 1-3/4 x .125 DOM x 60.000 INCHES LONG +or- .050 YIELD IS 4

PIECES PER 20 FOOT LENGTH

Clip Steel Mount Adjustable 351 Small Block Ford, Use With TCP Front

Clips Only. Welded Steel Construction. Adjusts Front to Rear in

Chassis. See Data Sheet For Oil Pan Fitment Info. Not For Use With

260-289-302 Engines

gStreet Chassis Billet Upright A-Arm Front Suspension Includes Billet

Aluminum Front Uprights, Wide-Trac Billet Upright Upper and Lower

Control Arms, Power Rack and Pinion with Bumpsteer Adjustable

Tierods, Splined Antiroll Bar, Varishock Coi-lOvers with Springs.

Bill Option 1 Option Code: 31 Tubular Control Arms Aluminum Wide-Track Upright

Bill Option 2 Option Code: 01 4-1/2 Bolt Circle Spindle In Front Aluminum Upright

Bill Option 3 Option Code: 57 POWER RACK BLACK 32" CSMBR 23.5" RACK CENTER

Bill Option 4 Option Code: 32 32" Frame Width Splined Arm Billet Mount Antiroll Bar

Bill Option 5 Option Code: 61 Pivot-Ball Q4 4-Way & Bolts Remote Reaservior

Bill Option 6 Option Code: 12 HEAVY SB ALL ENGINE MATERIALS CHEVY ENGINE 550 lb

Bill Option 7 Option Code: 02 14" - RED 6 PISTON CALIPER DRILLED & SLOTTED BLACK ROTOR

COILOVER BOLT SET, GRADE8, FOR A PAIR OF SHOCKS

Hardware 1/2-Stud Upright II/IRS 14" W4A/W6A Aero6 Caliper Includes

Hats, Caliper Brackets and Hardware for 14 x 1-1/4 Rotors with W4A or

W6A Aero6 Wilwood Calipers

Threaded 3/4 Bumpsteer 9/16 -18-Right Adjuster Sleeve Rack

Connection with 5/8 Left Hand Alloy Steel Rod End Tierod Use With

Street Machine Power Racks.

UPRIGHT FRONT ONE-PIECE S/M FRONT 4-1/2 Bolt Circle

CHASSISWORKS CLIPS, ALUMINUM BODY WITH UNIT-BEARING

SPINDLE INCLUDES STEERING ARM WITH 3/4 THREADED BORE

FOR 5/8 RODEND STYLE TIEROD END

FITMENT NOTE: MINIMUM RIM SIZE 18" DIAMETER DEPENDING

ON WIDTH.

Rack Mount SM 32" CrossmemberWith 6140-32-M40 Rack

Power Rack 32" Clip 3/4-36 Input Spline With 9/16-18 Tierods & 43-3/4

Tire Rod Length Left Hand Front Steer, For Street Machine Suspension

On 32" Outside Width Frame (65-70 Mustang) Use With Rack Mount

Set 6139-32-M40

A-ARMS UPPER WIDE-TRAC for BILLET ALUMINUM UPRIGHT ON

g-STREET MACHINE CROSSMEMBER

A-ARMS LOWER WIDE-TRAC for BILLET ALUMINUM UPRIGHT ON

g-STREET MACHINE CROSSMEMBER

SHOCK SIMULATOR FOR 12.0" RIDE HEIGHT

HARDWARE BOX 5735 SPLINED FRONT ANTIROLL BAR FOR ALL

G-MACHINE CLIPS

5735 - 32" CLIP SPLINED ARB FRONT ANTIROLL BAR G-MACHINE CLIPS WITH 32" OUTSIDE WIDTH

INSTALLATION GUIDE S/M A-ARMS

CO Q4 Remote Reservior Quad-Adjustable STD Pivot-129 Pivot-129

4.25 Travel, 14.31" Extended Length, Top Is Standard Pivot Ball with

1/2 Bore x 1.290 Long Sleeve, Base Is Standard Pivot Ball With 1/2

Bore x 1.290 Long Sleeve, KCR Valving

VARISPRINGS 9" LONG x 550 LB/RATE, SILVER POWDER COATED,

BOXED PAIR

W6A-RH AERO6 RED CALIPER 1-1/4 x 14/15" ROTORS, 6 PISTON

1.62/1.12/1.12, 7.090" RADIAL MOUNT, PASSENGER SIDE BEHIND

AXLE MOUNT, uses 6617 type Pads

W6A-LH AERO6 RED CALIPER 1-1/4 x 14/15" ROTORS, 6 PISTON

1.62/1.12/1.12, 7.090" RADIAL MOUNT, DRIVER SIDE BEHIND AXLE

MOUNT, uses 6617 type Pads

Pad W6/W4 Street & Performance BP-20 Smart Pad Causes Light

Dusting Polymatrix Type 6617 4 Pack

ROTOR SRP 1.25 x 14.00" PASSENGER

ROTOR SRP 1.25 x 14.00" DRIVER

Suspension Rocker-Arm IRS gStreet Clip & Chassis Includes UCA,

LCA, Toe-Links, Pushrod Rocker Arm System, FAB9 Center with Billet

Aluminum Rear Uprights, Stub Shafts with Halfshafts, Varishock

Coil-Overs with Springs. No Dropout Thirdmember Included. Optional:

Driveshaft Loop Pinion Support, Wheel Stud Pattern or Centerlock

Spindles, Shock Valving, Spring Rate, Splined Antiroll Bar & Brakes

Bill Option 1 Option Code: 54 Half Shafts for 54" Hub Width 64-70 Mustang

Bill Option 2 Option Code: 45 4-1/2 Bolt Circle Wheel Studs 1/2-20 Thread

Bill Option 3 Option Code: 02 Strange Pro-Aluminum Ford 9 Dropout Pinion Mount Included

Bill Option 4 Option Code: 04 COM-8 Q4 4-Way & Bolts Piggy-Back Remote Reaservior

Bill Option 5 Option Code: 50 Baseline Spring Rate 500 lb.

Bill Option 6 Option Code: 14 14 SRP 1/2-Studs Black Wilwood Caliper & E-Brake Mechanism

Bill Option 7 Option Code: 54 Splined Arm Antiroll Bar 54" Rear Hub Width

Bill Option 8 Option Code: ST Strange S-Trac Helical Gear 35 Spline Differential

Hardware 1/2-Stud Upright II/IRS 14" W4A/W6A Aero6 Caliper Includes

Hats, Caliper Brackets and Hardware for 14 x 1-1/4 Rotors with W4A or

W6A Aero6 Wilwood Calipers

Hardware E-Brake Unit Hub-A IRS Parking Brake Assembly for use with

8383-14 thru 8384-15 Brake Kits

IRS Tubular LCA Pivot-Ball Bearing Rodends Matte Black

IRS Toe-Links 5/8 Rodends with Bumpsteer Adjuster

IRS Tubular UCA Pivot-Ball Bearing Rodends Matte Black

Upright IRS 4-1/2 Bolt CircleAluminum Body With Unit-Hub Bearing

Spindle and Series 21Stub Shaft. Integal Toe-Link Arm With 3/4

Threaded Bore For 5/8 Rodend Style Toe-link End. Spindle Cap Has

2.780 Wheel Register Diameter.

FITMENT NOTE

Minimum Rim Size 18" Diameter Depending on Rim Width.

Shock IRS Rocker Assembly 1/2Rodends x 13.40 Long Link Rods For

IRS Pushrod Shocks

Pinion Support D/S Loop 9" Ford Strange HD Pro Aluminum Dropout

For IRS Includes Driveshaft Loop

ARB Splined Bar 7/8-48 x 0.88Solid Straight Arm Hardware Box For

5861-S-088-XXXX

Solid ARB 0.88 x 28.00 x 7/8-48 Spline Flat End for 5/8 Thick Arm for

54 Hub Width Rear IRS

FAB9 Assembly for IRS With 35Spline Stub Axles

Assembly Half Shaft CV Joints& Boots 35 Spline 45° PA 13.625 Overall

Length

Assembly Half Shaft CV Joints& Boots 35 Spline 45° PA 15.625 Overall

Length

INSTRUCTIONS & DRAWING FOR 8383-14 with UNIT HUB-AB

C/O PR LEFT Q4 COM8-1 4.25 TRAVEL QUAD ADJUSTABLE

PIGGYBACK RESERVIOR WITH COMPRESSION KNOBS ON LEFT

SIDE OF REBOUND KNOBS, COILOVER FOR 2-1/2 ID SPRINGS,

10.06 to 14.31 LENGTH, 1/2 BORE x 1" WIDE COM-8 BEARINGS IN

BOTH EYES, ROAD RACE RR VALVING, SHOCK ASSEMBLY WITH

3/4 EXTENDED UPPER COIL SPRING SEATS AND LOWER SPRING

SEAT

- SPECIAL ORDER PART NOT RETURNABLE FOR ANY REASONVAS

C/O PR RIGHT Q4 COM8-1 4.25 TRAVEL QUAD ADJUSTABLE

PIGGYBACK RESERVIOR WITH COMPRESSION KNOBS ON RIGHT

SIDE OF REBOUND KNOBS, COILOVER FOR 2-1/2 ID SPRINGS,

10.06 to 14.31 LENGTH, 1/2 BORE x 1" WIDE COM-8 BEARINGS IN

BOTH EYES, ROAD RACE RR VALVING, SHOCK ASSEMBLY WITH

3/4 EXTENDED UPPER COIL SPRING SEATS AND LOWER SPRING

SEAT

VARISPRINGS 8" LONG x 500 LB/RATE, SILVER POWDER COATED,

BOXED PAIR

VAS 523-100 SET 1.0000 0.0000 0.0000 COMPONENT

Anti-Rotation Shim COM-8 Shock Base 1.45 OD x .61 ID x .19 Long

Delrin, Set of 4 Pieces

W4A AERO4 Red CALIPER 1-1/4 x14/15" ROTORS, 4 PISTON

1.12/1.12, 7.090" RADIAL MOUNT, FITS BOTH SIDES, uses 6617 type

Pads

Pad W6/W4 Street & Performance BP-20 Smart Pad Causes Light

Dusting Polymatrix Type 6617 4 Pack

ROTOR SRP 1.25 x 14.00" PASSENGER

ROTOR SRP 1.25 x 14.00" DRIVER

Using a Strange S-Trac 35 Spline 9" Ford Differential. Not Inccluded, Requires Optional Purchase.

Fuel Tank -10 Supply M10 gStreet Rear Clip & Chassis 65-70 Mustang

Approximately 17 Gallon Capacity. Tank Only, Can Be Trunk or Remote

Filled. Requires Chassis Mounts, Fill Kit and Vent.

Fuel Tank Remote Fill Universal90° Hose For Rear Clip & Chassis.

Includes Aircraft Cap, Filler Tube with Hose and Recessed Ring to

Attach Cap To Rear TailLight Panel

5908-VC1 EACH 2.0000 0.0000 0.0000 149.0000 298.00

Vent Canister Billet AluminumBlack Anodized-6 Inlet With 40 Micron

Sintered Vent. Use for Fuel Tank, Axle Housing & Transmissions.

Require Mounting Bracket and Connecting Hose.

Vent Remote Breather With Premium Hose Contains-6 x 36" Black

Push-Lite Race Hose, One of Each Hose End, Straight, 45° and 90°, 40

Micron Sintered Vent, -6 Male x Female -8 ORB Bulkhead Fitting With

Jam Nut and Bolt-On Chassis Mounting Bracket. Use for Venting Fuel

Tank, Axle Housing & Transmissions.

Vent Can Premium Hose Only Contains -6 x 36" Black Push-Lite Race

Hose, 2 Hose Clamps and One of Each Hose End, Straight, 45° and

90°. Use to Attach Vent Can to Axle or Gas Tank.

RESERVOIR CLAMP x 1-5/8 TUBE PARALLEL AXIS STYLE

CONTAINS A PAIR OF MOUNTS TO ATTACH TWO2.225 od

RESERVOIR to 1-5/8 TUBE

DUAL SILO ANGLED 41° g-STREETSURFACE RESERVOIR MOUNT -

Contains single mount for two VariShock remote reservoirs. For use

with 7740-M10-R rear floor tin kit or 41-degree angled panel.

FORD-9 4.11 35 S-Trac HD Pro Aluminum DROPOUT Contains HD Pro D/S PART

Aluminum Housing, Oil Channel Pinion Support, 4.11ratio 8620

Gearset, 35 Spline Strange S-Trac Helical Gear Differential

Chromemoly 1350 Yoke

Differential Yoke U-Bolts 1350 Series U-Joint Yokes On Ford 9"

Dropout - Pair